LulzBot TAZ & Mini

• 3

  WorkHorse and Pro Z offset reapeatability
  • 3Dmachine

  1
  1
  Posts
  963
  Views

  No one has replied

• A

  Installing SL .25 Micro to TAZ 6
  • auxarchitecture

  2
  2
  Posts
  1107
  Views

  

  This one is strange, I cannot say I have seen this one before in particular. In this case, please reach out to us at Support@MatterHackers.com and we would be happy to do some digging.
• W

  Mini 2 and Z-axis lock?
  • wsanders

  3
  3
  Posts
  1674
  Views

  

  I wouldn't get a lulzbot until it becomes more clear as they will find a buyer and survive the "restructuring" They let about 90% of their workforce go. So I'd stick with something safer or open source where there is a good chance of getting parts and support
• W

  This topic is deleted!
  • wsanders

  1
  1
  Posts
  1
  Views

  No one has replied

• B

  TAZ Aerostruder vs it-works E3D Titan Aero toolhead
  • belezeebub

  2
  2
  Posts
  2535
  Views

  T

  Hi...in my case the adjustment screw for tension is overly difficult to adjust, and from the factory set very tightly. On the flip side you can sortve see where the filament is going if youre having trouble loading it. It doesnt seem to feed 1.75mm as well as the original extruder does, after a couple attempts just to see (since I had files sliced already) i gave up and sliced again. The fan mount is a bit better placed so you can still see the nozzle and get to it to clean it easier. I was disappointed that for the price it did not come with a silicone sock already on it. assembly and pcb
• U

  Droopy Overhangs
  • underdog1924

  4
  4
  Posts
  2260
  Views

  

  Here you go!
• 9

  I got an interesting one ..
  • 907jon

  2
  2
  Posts
  1771
  Views

  

  Hey @907jon I am sorry for us getting to this one so late but hopefully the information I am providing will be useful to others in the future! So this kind of issue is most of the time caused by the previously loaded material is not heating up to temp fully causing a slight blockage and excess pressure in the hotend results. In turn this will cause the feed system to grind up the material. To resolve this we would normally recommend to purge the ABS out with a cold pull which you can find the instructions for here. Give these a shot if you still run into issues or feel free to reach out to us. Thanks!
• A

  Lulzbot Taz 6 Stop Extruding But It Keeps Moving
  • ajusay74

  2
  2
  Posts
  1822
  Views

  

  @ajusay74 There could be several reasons for this issue. If it occurs at the same layer height for different types of filament, then it is most likely a firmware issue. Feel free to contact us directly if you need to do more of a deep dive on this issue.
• I

  White Pro PLA too soft?
  • Iguanaman

  2
  2
  Posts
  1747
  Views

  

  @Iguanaman This usually means that the hot end temperature is too low. Feel free to print with the Pro Series up to 230C and adjust down from there if necessary.
• 

  TAZ 6 with Dual Extruder v2
  • addaline

  3
  3
  Posts
  4264
  Views

  

  Thanks for the reply. I took a chance a just copied the wipe code into MatterControl, replacing the relevant section. Seems to work just fine. I'd be more comfortable if the bed didn't shoot so far forward, as the first tip *just* touches the wipe pad, but I'll worry about tweaking that later.The Y axis for the 2nd extruder was "-50" (*minus* being the key), and seems to be working fine after a couple of test prints. It's weird thinking about how the numbers will be interpreted, but fortunately everyone seems to follow the same co-ordinates, so the dual extruder calibration steps for the TAZ 6 seemed to work just fine in MatterControl. I did see the Printer Profile Bounty. Not sure that I would have any *significant* tweaking to qualify, but I'll keep it in mind.As an aside, love the "Preheat" buttons!Thanks,Dion
• 

  Printer's Physical Dimensions
  • AnotherDimension

  2
  2
  Posts
  3909
  Views

  

  What printer are you talking about?
• 

  Quick hack for printing Ninjaflex
  filament how to • • unlimitedbacon

  1
  1
  Posts
  5224
  Views

  No one has replied