---

General Discussion

• A

  Filament replacing
  • Al.Sarraf

  1
  1
  Posts
  177
  Views

  No one has replied

• 

  I Need Assistance Adjusting Fill Density in Fusion 360 and Cure for Various Parts
  • Belleann

  1
  1
  Posts
  350
  Views

  No one has replied

• W

  Pulse D-232 keeps pausing with "Jam, No Filament" No Jam.
  • Wscrivener

  2
  2
  Posts
  954
  Views

  

  Try turning run out sensor off in the settings. If your using matter control in the printer tab then hardware tab. Disable "has runout sensor". Obviously thats not fixing it but I'd bet the sensor is bad potentially.

• M

  Warranty on xtool p2 Laser Engraver
  • Marauder1911

  1
  1
  Posts
  1073
  Views

  No one has replied

• J

  Equal Spacing between objects
  • jcdelmore

  2
  2
  Posts
  2535
  Views

  H

  @jcdelmore said in Equal Spacing between objects:

  I have six cylinder object and I want to have equal spacing between them, how do I do it?

  Determine the total width or length available for placing the cylinders. Let's call this value "Total Width."

  Calculate the desired spacing between the cylinders. Divide the Total Width by the number of cylinders minus one (since there will be one less gap than the number of cylinders). Let's call this value "Spacing."

  Start by placing the first cylinder at the beginning of the available space.

  Place the second cylinder at a distance of Spacing from the first cylinder.

  Continue placing the remaining cylinders, each at a distance of Spacing from the previous cylinder.

• C

  Pulse XE wire off
  • ChadG

  1
  1
  Posts
  2453
  Views

  No one has replied

• O

  Pulse 3d printer concern:
  • ozzy5

  2
  2
  Posts
  3166
  Views

  

  @ozzy5 Pulse is a very reliable printer, parts are available at Matterhackers.

• M

  This topic is deleted!
  • monetize

  1
  1
  Posts
  4
  Views

  No one has replied

• 

  This topic is deleted!
  • apporio

  1
  1
  Posts
  5
  Views

  No one has replied

• A

  This topic is deleted!
  • aayanali

  1
  1
  Posts
  22
  Views

  No one has replied

• 

  This topic is deleted!
  • Simone006

  1
  1
  Posts
  46
  Views

  No one has replied

• M

  This topic is deleted!
  • mike147

  1
  1
  Posts
  14
  Views

  No one has replied

• 

  This topic is deleted!
  • cmsattamatka05

  1
  1
  Posts
  12
  Views

  No one has replied

• 

  This topic is deleted!
  • BuilderHardware

  1
  1
  Posts
  7
  Views

  No one has replied

• 

  This topic is deleted!
  • hanrymark450

  1
  1
  Posts
  3
  Views

  No one has replied

• 

  How MatterControl evaluate the bed boundaries with BLTouch Offset?
  • seaquest42

  2
  2
  Posts
  3845
  Views

  

  If your bed size is 220 x 220, then it is not rectangular. P1 should probe the bed center (G28) prior to bed mesh (G29). Make sure Has Z probe is on and z servo is also on.

• 

  This topic is deleted!
  • David90Johnson

  1
  1
  Posts
  14
  Views

  No one has replied

• G

  This topic is deleted!
  • GetSecurityaustin00

  1
  1
  Posts
  4
  Views

  No one has replied

• S

  This topic is deleted!
  • syamala

  1
  1
  Posts
  13
  Views

  No one has replied

• J

  This topic is deleted!
  • jooyasho

  1
  1
  Posts
  9
  Views

  No one has replied