I found that if I just wait long enough it does indeed start printing, but as you can see it still says heating to zero on the main screen. Here is the beginging of GCODE from terminal
->Communication State: PreparingToPrint->N1 M110 S1*96
<-ok
->Communication State: Printing
->N2 G21*24 [0.013]
<-ok [0.013]
->N3 M107*38 [0.014]
<-ok [0.036]
->N4 M104 T1 S230*37 [0.037]
<-ok [0.081]
->N5 M104 T1 S230*36 [0.082]
<-ok [0.126]
->N6 T1*61 [0.127]
<-ok [0.149]
->N7 G28*20 [0.151]
<-ok [0.229]
->N8 M114*47 [0.230]
<-ok
X:285 Y:150 Z:0 E:0 [0.252]->N9 G1 X285.1 Y149.9 Z3.144 F5000*30 [0.253]
<-ok [0.275]
->N10 M1200 MatterControl*125 [0.276]
<-ok [0.298]
->N11 M104 T1 S230*17 [0.301]
<-ok [0.345]
->N12 G4 P1000*111 [0.346]
<-ok [0.368]
->N13 G4 P1000*110 [0.369]
<-ok [0.391]
->N14 G4 P1000*105 [0.392]
<-ok [0.414]
->N15 G4 P1000*104 [0.415]
<-ok [0.437]
->N16 G4 P1000*107 [0.438]
<-ok [0.460]
->N17 G4 P1000*106 [0.461]
<-ok [0.483]
->N18 G4 P1000*101 [0.484]
<-ok [0.508]
->N19 G4 P1000*100 [0.509]
<-ok [0.531]
->N20 G4 P1000*110 [0.532]
<-ok [0.554]
->N21 G4 P1000*111 [0.555]
<-ok [0.583]
->N22 G4 P1000*108 [0.584]
<-ok [0.606]
->N23 G4 P1000*109 [0.607]
<-ok [0.629]
->N24 G4 P1000*106 [0.630]
<-ok [0.694]
->N25 G4 P1000*107 [0.695]
<-ok [0.717]
->N26 G4 P1000*104 [0.718]
<-ok [0.740]
->N27 G4 P1000*105 [0.741]
<-ok [0.763]
->N28 G4 P1000*102 [0.764]
<-ok [0.786]
->N29 G4 P1000*103 [0.787]
<-ok [0.814]
->N30 G4 P1000*111 [0.815]
<-ok [0.837]
->N31 G4 P1000*110 [0.838]
<-ok [0.860]
->N32 G4 P1000*109 [0.861]
<-ok [0.883]
->N33 G4 P1000*108 [0.884]
<-ok [0.911]
->N34 G4 P1000*107 [0.912]
<-ok [0.934]
->N35 G4 P1000*106 [0.935]
<-ok [0.957]
->N36 G4 P1000*105 [0.958]
<-ok [0.980]
->N37 G4 P1000*104 [0.981]
<-ok [1.007]
->N38 M105*28 [1.007]
<-ok T0:38 T1:199 [1.051]
->N39 G4 P1000*102 [1.052]
<-ok [1.074]
->N40 G4 P1000*104 [1.075]
<-ok [1.097]
->N41 G4 P1000*105 [1.098]
<-ok [1.120]
->N42 G4 P1000*106 [1.121]
<-ok [1.143]
->N43 G4 P1000*107 [1.144]