@mpirringer Thank you so much for your input.
vbwstripes
@vbwstripes
Posts made by vbwstripes

Issue with Bed Temperature
Hello,
I have been unable to print because of an issue that I am seeing where the bed temperature reading goes to 150C when it starts to ramp up to the desired temperature. The bed does not actually heat up because the error occurs. I tried moving the wires around that go to the bed, calling support, and emailing with no help yet after several days. MH basically said they are busy and they'll call me back. I'm wondering if anyone else has seen this error? Thanks for any help.
ERROR: MINTEMP or MAXTEMP triggered on B. Check your temperature sensors!
HALT asserted  reset or M999 requiredTerminal log:
Communication State: PreparingToPrint
Generating Config
Starting slicerMatterSlice version 2.20.11
N78 M105*24
Optimized model: 0.3s
ok T:28.9 /0.0 @0 B:25.9 /0.0 @0
Sliced model: 0.3s
Generated layer parts: 0.1s
Processing support regionsProcessed support regions: 0.0s
N79 M105*25ok T:28.9 /0.0 @0 B:25.9 /0.0 @0
N80 M105*31ok T:28.9 /0.0 @0 B:26.1 /0.0 @0
Wrote layers: 1.88s
Total time elapsed 2.32s
Print time: 2049
Filament: 3341
Filament2: 0
N81 M105*30ok T:28.8 /0.0 @0 B:26.9 /0.0 @0
N1 M110 N1*125ok
Communication State: Printing
N2 M114*37ok X:0.0000 Y:0.0000 Z:0.0000 E:0.0000
N3 M117 Printing  0%*14ok
N4 G21*30ok
N5 M107*32ok
N6 M140 S35*85ok
N7 M104 T0 S200*36ok
N8 M140 S35*91ok
N9 M105*46ok T:28.8 /200.0 @255 B:27.3 /35.0 @255
N10 M105*22ok T:28.9 /200.0 @255 B:27.6 /35.0 @255
N11 M105*23ok T:29.2 /200.0 @255 B:27.7 /35.0 @255
N12 M105*20ok T:29.9 /200.0 @255 B:28.3 /35.0 @0
N13 M105*21ok T:31.1 /200.0 @255 B:31.6 /35.0 @0
N14 M105*18ok T:32.8 /200.0 @255 B:103.8 /35.0 @0
ERROR: MINTEMP or MAXTEMP triggered on B. Check your temperature sensors!
HALT asserted  reset or M999 required
N15 M105*19ok T:34.8 /0.0 @0 B:145.9 /0.0 @0
N16 M105*16ok T:36.8 /0.0 @0 B:147.0 /0.0 @0
N17 G1 Z1.67 E0.833 F1800*123!!
N18 M105*30ok T:41.7 /0.0 @0 B:147.7 /0.0 @0
N19 G1 Z3.34 E1.667*16!!
N20 M105*21ok T:43.9 /0.0 @0 B:147.2 /0.0 @0
N21 G1 Z5 E2.5*53!!
N22 M105*23ok T:45.3 /0.0 @0 B:146.5 /0.0 @0
N23 G1 Z6.67 E3.333*28!!
N24 M105*17ok T:46.1 /0.0 @0 B:146.5 /0.0 @0
N25 G1 Z8.34 E4.167*22!!
N26 M105*19ok T:46.4 /0.0 @0 B:146.8 /0.0 @0
N27 G1 Z10 E5*27!!
N28 M105*29ok T:46.4 /0.0 @0 B:147.0 /0.0 @0
N29 G90*43!!
N30 M105*20ok T:45.2 /0.0 @0 B:145.6 /0.0 @0
N31 M300 S3000 P30*17!!
N32 M105*22ok T:43.6 /0.0 @0 B:142.5 /0.0 @0
N33 M300 S1500 P30*20!!
N34 M105*16ok T:42.0 /0.0 @0 B:145.2 /0.0 @0
N35 M300 S3000 P30*21!!
N36 M105*18ok T:40.5 /0.0 @0 B:144.8 /0.0 @0
N37 M300 S1500 P30*16!!
N38 M105*28ok T:39.1 /0.0 @0 B:145.3 /0.0 @0
N39 M300 S3000 P30*25!!
N40 M105*19ok T:38.1 /0.0 @0 B:146.9 /0.0 @0
N41 M300 S1500 P30*17!!
N42 M105*17ok T:37.6 /0.0 @0 B:147.1 /0.0 @0
N43 M300 S3000 P30*20!!
N44 M105*23ok T:37.1 /0.0 @0 B:147.1 /0.0 @0
N45 M300 S1500 P30*21!!