MatterControl communication problem with Marlin on MEndelmax XL
-
Hello everybody,
I'm new to this forum and very glad to be here.
I'm currently trying to use my Mendelmax XL with Matter Control but I have some trouble. The connection between PC and printer seems to be fine and actually can manually move the X axis. But no way at all to move other axis, heating extruder or bed. I just got a small movement on the Y axis at the beginning but that's all. Also I got some small movement on Z axis but with big delay between the issue of the command and the execution.
I don't get any error message or warning. It simply just works properly only with the X axis.
I also tried different communication speeds but no luck.
To be noticed that I'm currently using for my prints Repetier Host and everything works like a charm. So it seems not to be an hardware problem.
Some info about my hardware and software setup:
- Laptop HP Envy Intel core i7
- Ubuntu 16.04 64 bit
- MatterControl 1.6 just downloaded from the official site
- Marlin V5
- Arduino Mega 2560
- Ramps 1.4
If you need further info just let me know.
Thanks in advance!
-
Can you try some movements and then post a terminal log? Often printers will refuse to move if they are having some kind of an error. The terminal log will show us if the printer is reporting any error messages.
-
Yep, I'll try during this weekend!
-
Here's the log file.
Again I was able to move X axis, some small movement on Y axis, some small movement on Z axis but the printer is mostly not responding.
Let me know if you need further information.
THanks!
->Communication State: AttemptingToConnect
->N0 M110 N1*124
<-ok
->Communication State: Connected->N0 M110 N1*124
<-ok
<-ok
->N0 M110 N1*124<-start
->N1 M105*38<-echo:Marlin 1.1.0-RC2
<-echo: Last Updated: 2015-09-28 12:00 | Author: (none, default config)
<-Compiled: Mar 18 2017
<-echo: Free Memory: 3455 PlannerBufferBytes: 1232
<-echo:V21 stored settings retrieved (380 bytes)
<-echo:Steps per unit:
<-echo: M92 X80.00 Y80.00 Z4000.00 E95.00
<-echo:Maximum feedrates (mm/s):
<-echo: M203 X700.00 Y700.00 Z3.00 E25.00
<-echo:Maximum Acceleration (mm/s2):
<-echo: M201 X1000 Y700 Z100 E10000
<-echo:Accelerations: P=printing, R=retract and T=travel
<-echo: M204 P1000.00 R3000.00 T3000.00
<-echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
<-echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
<-echo:Home offset (mm):
<-echo: M206 X0.00 Y0.00 Z-0.20
<-echo:Material heatup parameters:
<-echo: M145 M0 H180 B70 F0
<-echo: M145 M1 H240 B110 F0
<-echo:PID settings:
<-echo: M301 P31.24 I3.24 D75.23 C100.00 L20
<-echo:Filament settings: Disabled
<-echo: M200 D3.00
<-echo: M200 D0
<-echo:SD init fail
<-ok T:0.0 /0.0 B:0.0 /0.0 T0:0.0 /0.0 @:0 B@:0
->N2 M105*37<-ok T:33.4 /0.0 B:63.1 /0.0 T0:33.4 /0.0 @:0 B@:0
->N3 M115*37<-FIRMWARE_NAME:Marlin 1.1.0-RC2 From Archive SOURCE_CODE_URL:http:// ... PROTOCOL_VERSION:1.0 MACHINE_TYPE:MakergalV52 EXTRUDER_COUNT:1 UUID:0001-MendelMaxXLV5-MakerGal
<-ok
->N4 M114*35<-X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0.00 Y:0.00 Z:0.00
<-ok
->N5 M105*34<-ok T:33.2 /0.0 B:62.9 /0.0 T0:33.2 /0.0 @:0 B@:0
->N6 M105*33<-ok T:33.1 /0.0 B:62.9 /0.0 T0:33.1 /0.0 @:0 B@:0
->N7 M105*32<-ok T:33.1 /0.0 B:62.9 /0.0 T0:33.1 /0.0 @:0 B@:0
->N8 M105*47<-ok T:33.1 /0.0 B:62.9 /0.0 T0:33.1 /0.0 @:0 B@:0
->N9 M105*46<-ok T:33.1 /0.0 B:62.8 /0.0 T0:33.1 /0.0 @:0 B@:0
->N10 M105*22<-ok T:33.1 /0.0 B:62.7 /0.0 T0:33.1 /0.0 @:0 B@:0
->N11 M105*23<-ok T:33.1 /0.0 B:62.7 /0.0 T0:33.1 /0.0 @:0 B@:0
->N12 M105*20<-ok T:33.1 /0.0 B:62.7 /0.0 T0:33.1 /0.0 @:0 B@:0
->N13 M105*21<-ok T:33.1 /0.0 B:62.7 /0.0 T0:33.1 /0.0 @:0 B@:0
->N14 M105*18<-ok T:33.1 /0.0 B:62.6 /0.0 T0:33.1 /0.0 @:0 B@:0
->N15 M105*19<-ok T:33.1 /0.0 B:62.6 /0.0 T0:33.1 /0.0 @:0 B@:0
->N16 M105*16<-ok T:33.1 /0.0 B:62.6 /0.0 T0:33.1 /0.0 @:0 B@:0
->N17 M105*17<-ok T:33.1 /0.0 B:62.6 /0.0 T0:33.1 /0.0 @:0 B@:0
->N18 M105*30<-ok T:33.1 /0.0 B:62.5 /0.0 T0:33.1 /0.0 @:0 B@:0
->N19 M105*31<-ok T:33.1 /0.0 B:62.4 /0.0 T0:33.1 /0.0 @:0 B@:0
->N20 M105*21<-ok T:33.1 /0.0 B:62.4 /0.0 T0:33.1 /0.0 @:0 B@:0
->N21 M105*20<-ok T:33.1 /0.0 B:62.4 /0.0 T0:33.1 /0.0 @:0 B@:0
->N22 M105*23<-ok T:33.1 /0.0 B:62.4 /0.0 T0:33.1 /0.0 @:0 B@:0
->N23 M105*22<-ok T:33.1 /0.0 B:62.3 /0.0 T0:33.1 /0.0 @:0 B@:0
->N24 G1 X1 F6000*55<-ok
->N25 G90*39<-ok
->N26 M105*19<-ok T:33.1 /0.0 B:62.3 /0.0 T0:33.1 /0.0 @:0 B@:0
->N27 G1 X2*87<-ok
->N28 G90*42<-ok
->N29 G1 X3*88<-ok
->N30 G90*35<-ok
->N31 M105*21<-ok T:33.0 /0.0 B:62.3 /0.0 T0:33.0 /0.0 @:0 B@:0
->N32 M105*22<-ok T:33.0 /0.0 B:62.2 /0.0 T0:33.0 /0.0 @:0 B@:0
->N33 G1 Y-1 F3000*24<-ok
->N34 G90*39<-ok
->N35 M105*17<-ok T:32.8 /0.0 B:62.2 /0.0 T0:32.8 /0.0 @:0 B@:0
->N36 G1 Y0*84<-ok
->N37 G90*36<-ok
->N38 M105*28<-ok T:32.8 /0.0 B:62.1 /0.0 T0:32.8 /0.0 @:0 B@:0
->N39 G1 Y1*90<-ok
->N40 G90*36<-ok
->N41 M105*18<-ok T:32.8 /0.0 B:62.1 /0.0 T0:32.8 /0.0 @:0 B@:0
->N42 M105*17<-ok T:32.8 /0.0 B:62.1 /0.0 T0:32.8 /0.0 @:0 B@:0
->N43 G1 Y2*84<-ok
->N44 G90*32<-ok
->N45 M105*22<-ok T:32.8 /0.0 B:62.0 /0.0 T0:32.8 /0.0 @:0 B@:0
->N46 G1 Y1*82<-ok
->N47 G90*35<-ok
->N48 M105*27<-ok T:32.8 /0.0 B:61.9 /0.0 T0:32.8 /0.0 @:0 B@:0
->N49 G1 Y0*92<-ok
->N50 G90*37<-ok
->N51 M105*19<-ok T:32.8 /0.0 B:61.9 /0.0 T0:32.8 /0.0 @:0 B@:0
->N52 G1 Y-1*122<-ok
->N53 G90*38<-ok
->N54 G1 Y-2*127<-ok
->N55 G90*32<-ok
->N56 M105*20<-ok T:32.8 /0.0 B:61.9 /0.0 T0:32.8 /0.0 @:0 B@:0
->N57 G1 Y-3*125<-ok
->N58 G90*45<-ok
->N59 G1 Y-4*116<-ok
->N60 G90*38<-ok
->N61 G1 Y-5*126<-ok
->N62 G90*36<-ok
->N63 M105*18<-ok T:32.8 /0.0 B:61.8 /0.0 T0:32.8 /0.0 @:0 B@:0
->N64 G1 Y-4*122<-ok
->N65 G90*35<-ok
->N66 M105*23<-ok T:32.8 /0.0 B:61.8 /0.0 T0:32.8 /0.0 @:0 B@:0
->N67 G1 Y-3*126<-ok
->N68 G90*46<-ok
->N69 M105*24<-ok T:32.8 /0.0 B:61.8 /0.0 T0:32.8 /0.0 @:0 B@:0
->N70 M105*16<-ok T:32.8 /0.0 B:61.8 /0.0 T0:32.8 /0.0 @:0 B@:0
->N71 M105*17<-ok T:32.7 /0.0 B:61.7 /0.0 T0:32.7 /0.0 @:0 B@:0
->N72 M105*18<-ok T:32.8 /0.0 B:61.7 /0.0 T0:32.8 /0.0 @:0 B@:0
->N73 M105*19<-ok T:32.8 /0.0 B:61.6 /0.0 T0:32.8 /0.0 @:0 B@:0
->N74 M105*20<-ok T:32.8 /0.0 B:61.6 /0.0 T0:32.8 /0.0 @:0 B@:0
->N75 M105*21<-ok T:32.8 /0.0 B:61.6 /0.0 T0:32.8 /0.0 @:0 B@:0
->N76 M105*22<-ok T:32.8 /0.0 B:61.5 /0.0 T0:32.8 /0.0 @:0 B@:0
->N77 M105*23<-ok T:32.7 /0.0 B:61.5 /0.0 T0:32.7 /0.0 @:0 B@:0
-
Unfortunately the log does not show anything unusual. Can you try downloading the 1.7 beta and see if that works any better?
-
I will, thanks.
-
@unlimitedbacon Unfortunately the 1.7 release is not available for linux
-
I posted a link to the beta above. Here it is again.
https://mattercontrol.appspot.com/downloads/mattercontrol-linux/pre-release
-
@unlimitedbacon thanks, actually it looks better, now it is much more responsive. I will try some print soon as soon and post the results!